Cannondale headshok fatty ultra manual. 1999 headshok super fatty sl and fatty sl owners manual, 1999 headshok ® super fatty ® sl. Kenmore Lawn Mower User Manual. 4pk Flanged Ball Bearing Wheelbarrow Cart Bearings Lot For Lawn. Pair Of Cannondale Bicycle Headset Bearings Headshok Si Fatty. Vintage Skateboard Oj Super. • 129184 E-SERIES. OWNER’S MANUAL SUPPLEMENT. • In this supplement, particularly important information is presented in the following ways: Indicates a hazardous situation which, if not WARNING avoided, could result in death or serious injury. Indicates special precautions that must be NOTICE taken to avoid damage. A TIP provides helpful information. This manual meets EN standards 14764, 14766, and 14781. • Be sure to obtain and read all of them. Headshok sUsPensIon fork.18 If you need a manual or supplement, or have a question about your bike, please contact your Cannondale Dealer maIntenanCe.20 immediately, or call us at one of the telephone numbers listed on the back cover of this manual. • It is not a moped or motorcycle. In EU contries, (including fitting your bike with additional equipment) it is known legally as an “EpaC” cycle or Electrically necessary to comply with local laws. Ask your Cannondale powered assisted Cycle. Dealer for more information about operating an electrically assited pedal bicycle in your area. • Disconnect the battery from the charger unit when fully you must read and follow the BosCH battery and charger. Do not leave a fully charged battery connected instructions. Go to: to the charger. Unplug the charger from the wall outlet manual_ebikes/ when not in use. • Parts of the e-serIes BIke frame figure 1. BosCH Drive Unit 9. Headshok stem 18. BosCH speed sensor 2. BosCH Battery 10. Lockout lever 19. Rear Cassette 3. BosCH HMI Unit 11. Front Chainring 4. Headshok Fork 12. Drive chain, front chain ring, rear cassette, rear derailleur, crankarm) must be serviced by your Cannondale Dealer. Replacement parts must be identical to the original Cannondale specification for the bike. See specifications. Failure to replace components with original specification can result in serious overload or other damage to the drive unit. • BosCh handlebar mounted Interface (hmI) TURBO SPORT TOUR KM/H PMWH KM/H Reichweite Indication elements, drive hmI 1. Display-function button “i” 11. Display-function button “i” on the a. Motor-output indicator 2. Illumination button operating unit 3. Drive HMI 12. Reduce value/scroll down button “–” b. • E-Series Owner’s Manual Supplement - 129184.PDF BosCh lithium Ion Battery Pack / Charger 19. Holder of the rack-type 25. Upper holder of the standard 31. Plug-in connector battery pack battery pack 32. Ventilation openings 20. Rack-type battery pack 26. Standard battery pack 33. • BosCh technical data eBike system PowerPack PowerPack Drive Unit Drive Unit Cruise lithium ion battery pack 0 275 007 006/ article number article number 0 275 007 007 – standard battery pack, power output black 0 275 007 500 0 275 007 503 –. • E-Series Owner’s Manual Supplement - 129184.PDF oPeratInG InstrUCtIons Checking the Battery Pack Before Using for Charge-control Indicator the first time When the battery pack is switched on, the five green lEDs of the charge-control indicator 21 indicate the charge condition Check the battery pack before charging it or using it with your of the battery pack. • switching on and off notes for optimum handling of the Battery Pack switching the battery pack on is one of the possibilities to start the eBike system. Read and observe the operating The battery-pack life can be prolonged when being properly in-structions of the drive unit and the drive HMI. • E-Series Owner’s Manual Supplement - 129184.PDF Initial operation options for switching off the eBike system: ■ press the on/off button 5 of the drive HMI. Requirements ■ switch the battery pack off by its on/off button (see The eBike system can only be activated when the following battery pack operating instructions.) requirements are met: ■ Remove the drive HMI out of its holder. • setting the assistance level switching the drive hmI on/off To switch on the drive HMI, briefly press the on/off button 5. The level of assistance of the eBike drive when pedaling can be adjusted via the drive HMI. The assistance level can be When the internal battery pack is sufficiently charged, the drive HMI can also be switched on when not inserted in the holder. • E-Series Owner’s Manual Supplement - 129184.PDF range estimate (at selected assistance level) PowerPack 300 PowerPack 400 “TURBO” “TURBO” “SPORT” “SPORT” “TOUR” “TOUR” “ECO” “ECO” Mix* Mix* 80 100 120 140 160 180 200 80 100 120 140 160 180 200 speed estimate (at selected assistance level) PowerPack 300 PowerPack 400. • switching the Push-assistance mode on/ speed and distance Indication The speed indication e always displays the current speed. The push-assistance feature makes it easier to push the eBike.
0 Комментарии
Оставить ответ. |
АвторНапишите что-нибудь о себе. Простой обзор без лишних прикрас. Архивы
Март 2019
Категории |